Sterilizer down? Your OR schedule is down with it.
MBMTS repairs, calibrates and maintains steam sterilizers across Texas — with a guaranteed response in under 8 business hours (24/7) and audit-ready documentation on every visit.
⚡ Emergency autoclave service — call now:
[ Request Service ] [ Call Now ]
Serving hospitals, surgery centers, dental practices and clinics within a 300-mile radius of Dallas.
When Your Autoclave Fails, Everything Stops
An autoclave is one of the few machines in a healthcare facility that can shut down an entire department on its own. When a sterilizer goes offline, instrument trays stop moving. Cases get pushed. Sterile Processing starts flash-sterilizing under pressure, and the risk of a reprocessing error climbs.
The cost is rarely the repair itself. It's the cancelled procedures, the overtime, and the exposure during your next survey.
Mr. Biomed Tech Services provides autoclave maintenance service, emergency repair, calibration and replacement support for healthcare facilities across Texas. Our technicians are trained through respected Texas programs including CBET and TSTC, and every service visit produces documentation you can hand directly to a surveyor.
Common Autoclave Problems We Repair
Most sterilizer failures give warning signs before they become shutdowns. These are the issues our technicians see most often:
- Autoclave not reaching temperature — usually a failing heating element, a faulty temperature sensor, or a steam supply problem. Cycles run long or abort entirely.
- Failed biological or chemical indicators — a positive BI is a sterility assurance emergency. It can point to a sterilizer malfunction, poor steam quality, or a loading and operator issue.
- Door gasket leaks — worn or hardened gaskets let steam escape, so the chamber never holds pressure. One of the most common and most preventable faults.
- Chamber pressure faults — a defective pressure switch, blocked relief valve, or vacuum pump wear will throw the cycle off specification.
- Wet packs — trays coming out damp compromise sterility. Causes range from steam quality and condensate drainage to overloading and inadequate drying time.
- Vacuum pump failure — dynamic-air-removal sterilizers that can't pull a proper vacuum will fail Bowie-Dick testing.
- Drain and trap blockages — scale, debris and biofilm restrict drainage and cause erratic cycles.
- Control board and display faults — error codes, frozen panels, or printers that stop recording cycle data leave you without proof of a successful cycle.
- Water quality damage — poor feed water causes scale buildup that shortens chamber and element life. AAMI ST108 now addresses water quality specifically for this reason.
Our Autoclave Services
Preventive Maintenance & Inspection
Scheduled PM based on manufacturer specifications: gaskets, valves, traps, filters, sensors, vacuum systems, safety devices and drainage. We clean, lubricate, adjust and replace wear parts before they fail — and document every step.
Emergency Repair
Sterilizer offline? We diagnose, quote honestly, and repair with quality parts. Response guaranteed in under 8 business hours (24/7).
Calibration & Performance Verification
Temperature, pressure and timing verified against specification, with a calibration certificate for your records.
Post-Repair Qualification Support
Qualification testing is required when a sterilizer is newly installed, relocated, has malfunctioned, or has undergone a major repair. We coordinate with your SPD team so the unit is properly re-qualified before it returns to service. Infection Control Today
Rental & Loaner Sterilizers
Facility can't wait? Our medical equipment rental program supplies tabletop and free-standing autoclaves on flexible short-term terms — inspected and ready for use.
Sales & Replacement
New and certified reconditioned sterilizers, with a standard 90-day warranty on refurbished units.
Disposition
Retiring an old sterilizer? We handle safe, compliant removal and help you recover value where possible.
⚡ Autoclave down right now?
Don't cancel your cases. Call +1 (469) 767-8853 — technician response in under 8 business hours across Texas.
[ Request Emergency Service ]
Sterilizer Brands & Models We Service
Our technicians work on the tabletop and free-standing sterilizers most commonly found in Texas facilities:
- Tuttnauer — tabletop and large-chamber steam sterilizers
- Midmark — M9, M11 and related tabletop autoclaves
- Belimed — free-standing and washer-disinfector systems
- Getinge, STERIS, Scican, Amsco and other major platforms
Don't see your sterilizer listed? We most likely service it. Send us the model number →
MBMTS is an independent biomedical service provider and is not affiliated with, or authorized by, the manufacturers named above. Brand names are used only to describe the equipment we service.
Compliance & Documentation You Can Hand to a Surveyor
Sterilizer records are among the first things infection prevention surveyors ask for. The Joint Commission reviews device reprocessing policies, sterilizer cycle documentation, and the frequency of chemical and biological testing. Envigilance
Every MBMTS service visit includes:
- ✅ Dated inspection and service report
- ✅ Calibration certificate with recorded parameters
- ✅ Parts replaced and work performed, itemized
- ✅ Records aligned with AAMI ST79, Joint Commission and OSHA expectations
- ✅ Technicians trained through CBET and TSTC programs
Repair, Rent or Replace? A Quick Decision Guide
| Situation | Best option |
|---|---|
| Single component failure, unit otherwise sound | Repair |
| Repair cost approaching 50%+ of replacement value | Replace |
| Repeated failures across multiple cycles | Replace |
| Parts obsolete or no longer supported | Replace |
| Temporary capacity gap or unit awaiting repair | Rent |
| Budget approved next fiscal year | Rent now, buy later |
Not sure where your unit falls? Our biomedical consultancy team gives an honest assessment. We're independent of any manufacturer, so the recommendation is based on your budget — not a sales quota.
📋 Free Download: Autoclave Preventive Maintenance Checklist
A practical, printable PM checklist built for Sterile Processing and biomed teams — daily, weekly, monthly and annual tasks in one page, aligned with AAMI ST79 documentation practices.
Get the checklist:
Name · Work Email · Facility
[ Send Me the Checklist ]
Autoclave Service Across Texas
We serve hospitals, surgery centers, dental offices, labs and clinics within a 300-mile radius of Dallas:
Dallas · Fort Worth · Houston · Austin · San Antonio · Waco · Lubbock — plus surrounding areas in Oklahoma and Louisiana.
Frequently Asked Questions
How often should an autoclave be serviced?
Preventive maintenance is typically scheduled quarterly to annually depending on cycle volume and manufacturer guidance. Separately, AAMI ST79 recommends that biological monitoring of steam sterilization cycles be performed routinely — weekly, and preferably daily — as well as for every load containing implants. High-volume SPDs generally need more frequent professional service than a low-volume dental practice. Infection Control Today
My autoclave isn't reaching temperature. What's wrong?
The most common causes are a failing heating element, a faulty temperature sensor, inadequate steam supply, or scale buildup from poor water quality. Take the unit out of service and have it diagnosed before running patient-care loads through it.
What should I do after a failed biological indicator?
Remove the sterilizer from service, quarantine affected loads, and investigate. AAMI ST79 provides a decision tree and checklist for investigating sterilization process failures, covering causes such as operator error, inadequate steam quality, and sterilizer malfunction. Our technicians support that investigation from the equipment side. Aami
Do I need testing after an autoclave repair?
Yes. Qualification testing is performed after a sterilizer malfunctions or after a major repair, before the unit returns to routine use. We coordinate with your SPD team on this. Infection Control Today
How fast can you get a technician on site?
We guarantee a response in under 8 business hours anywhere in our Texas service area.
Do you service dental office autoclaves?
Yes. We support tabletop sterilizers in dental practices, clinics and ambulatory surgery centers, not just large hospital systems.
Can I rent a sterilizer while mine is repaired?
Yes. We offer short-term autoclave rentals so your facility keeps operating during downtime.
🔴 Get Your Autoclave Back in Service
Don't wait for a failed load or a survey finding. Whether you need emergency repair, a PM contract, a rental unit or a replacement — MBMTS responds fast and prices fairly.
📞 Call +1 (469) 767-8853
Request service — takes 30 seconds:
Name · Phone · Equipment Type (dropdown) · Describe the issue
[ Request Service ]
Response guaranteed in under 8 business hours · Serving all of Texas
Leave a Comment
Comments [0]
No comments available for this blog.