A CO2 module adds capnography, the measurement of exhaled carbon dioxide, to a patient monitor. For Dallas surgery centers, endoscopy suites, dental and oral surgery offices and procedure rooms that sedate patients, it is often the piece of monitoring that turns an adequate setup into a compliant one. This guide explains the types of CO2 measurement, how to make sure a module works with your monitors, and what to check on a refurbished unit. CO2 modules and monitors are part of our new and refurbished medical equipment for sale.
Why capnography matters
Pulse oximetry shows oxygen saturation, but it can lag behind a breathing problem, especially when a patient is on supplemental oxygen. Capnography shows each breath as a waveform and gives an end-tidal CO2 (EtCO2) number and respiratory rate, so a slowing or obstructed airway shows up quickly. The American Society of Anesthesiologists' monitoring standards, summarized by OpenAnesthesia, call for continual end-tidal CO2 monitoring during general anesthesia, to confirm endotracheal tube or supraglottic airway placement, and during moderate or deep sedation. If your facility sedates patients, you need a reliable way to measure exhaled CO2.
The three ways to measure CO2
| Type | How it works | Best for |
|---|---|---|
| Mainstream | The sensor sits on an airway adapter at the patient's breathing circuit | Intubated patients; fast response, no sample line |
| Sidestream | A pump draws a small gas sample through a tube to the module | Intubated and non-intubated patients; sensor away from the airway |
| Low-flow sidestream | A small sample flow through a dedicated nasal/oral cannula | Sedation of non-intubated patients, neonates and procedure rooms |
For sedation in endoscopy, dental or procedure rooms, a sidestream system with a nasal/oral sampling cannula is usually the practical choice. For ventilated patients, mainstream or sidestream both work well.
Compatibility: the most important check
CO2 modules are rarely universal. Most plug into a specific monitor family's module rack or connector, and some monitors have built-in CO2 that is enabled by a software license. Before you buy:
- Confirm the module's exact part number is supported by your monitor model and software version.
- Check whether the monitor needs a license or software option to display CO2.
- Confirm the module sends data to your central station if you use one.
- Check that the waveform and alarms appear correctly on every monitor that will use the module.
If you are still choosing monitors, our patient monitor buying guide explains which monitor families offer CO2 as a module or built-in option.
Consumables: the ongoing cost
- Sidestream: sampling lines, cannulas, water traps or filters, usually single-patient use.
- Mainstream: airway adapters, either single-use or reusable.
- Proprietary supplies: some technologies require the manufacturer's own sampling lines. Check availability and price per patient.
Over the life of the module, consumables usually cost more than the module itself.
Refurbished CO2 modules: what to check
- Accuracy: tested with a calibration gas of known CO2 concentration; reading should match within the manufacturer's tolerance.
- Calibration status: many sidestream modules need periodic calibration; ask when it was last done and when it is next due.
- Pump and flow: sidestream pumps should draw the specified sample flow and detect occlusions.
- Response time and waveform: a clean capnogram with correct respiratory rate on a simulator or test lung.
- Alarms: high and low EtCO2, apnea and occlusion alarms.
- Operating hours: some modules log hours and need service at set intervals.
- Connector and housing: no cracks or bent pins.
Our patient monitor repair and calibration guide covers EtCO2 checks alongside the other monitor parameters. Reconditioned modules from us come with a 90-day warranty.
What the waveform tells staff
A normal capnogram rises sharply as the patient breathes out, levels into a plateau and drops back to zero as they breathe in. A rising EtCO2 with slower breaths suggests the patient is under-breathing from sedation. A waveform that shrinks or disappears can mean an obstructed airway, apnea or a displaced cannula. A baseline that does not return to zero suggests rebreathing or a saturated water trap. Teaching staff these few patterns gives them earlier warning than oxygen saturation alone, which is the reason to buy the module in the first place.
Setting up capnography in a sedation room
- Set default EtCO2 and apnea alarm limits that match your sedation policy.
- Stock sampling cannulas for every size of patient you sedate.
- Train staff to read the waveform, not just the number; a flat line can mean apnea or a disconnected line.
- Check the module before the first case each day.
Delivery and service in Dallas–Fort Worth
For in-stock modules, delivery can usually be scheduled the same day across Dallas–Fort Worth, and we can confirm the module works with your monitors on site. Service requests receive a response in under 8 business hours, Monday through Friday, with same-day on-site support from our Garland headquarters.
To find a CO2 module that fits your monitors, call (469) 767-8853 or send us a request with your monitor model.
Leave a Comment
Comments [0]
No comments available for this blog.