An IV pump that looks perfect can still deliver the wrong volume. Flow accuracy, occlusion alarms and air detection can only be confirmed with test equipment, which is why a refurbished IV pump is only as trustworthy as the testing behind it. This page explains the checks our engineers run on every refurbished IV pump before it leaves our Garland headquarters, and what you should ask any seller to show you. Pumps are part of our new and refurbished medical equipment for sale.

Before testing: is this pump worth refurbishing?
- Recall status: infusion pumps have had many recalls and field corrections. We check the model in the FDA medical device recall database and confirm the required updates were completed on that serial number.
- Support status: parts, administration sets and software updates must still be available for the model.
- Fleet fit: the pump should match the model and software your facility already uses, or come with a plan for training.
The test sequence
1. Physical inspection
Housing, pole clamp, door and latch, keypad, display, power cord, battery door and the pumping mechanism. Cracks or a loose door latch are replaced, not noted.
2. Power and battery
The pump must start cleanly, pass its self-test and run on battery for the time the manufacturer specifies. Batteries are the most common failure in used pumps, so tired batteries are replaced and the date recorded.
3. Flow-rate accuracy
Using an infusion device analyzer, we measure the delivered volume at several rates, including low rates where errors are most likely, and compare it with the manufacturer's accuracy specification.
4. Bolus and volume-to-be-infused
Where the pump offers boluses or stops after a set volume, we confirm the delivered amount matches what was programmed and that the pump switches to keep-vein-open or stops as designed.
5. Occlusion detection
We create downstream and, where the pump supports it, upstream occlusions and record the pressure and time at which the alarm sounds. A pump that alarms too late can let pressure build in the line; one that alarms too early interrupts therapy.
6. Air-in-line detection
We introduce air into the set and confirm the pump stops and alarms.
7. Door, set and alarm checks
Door-open, set-not-loaded, empty-container and low-battery alarms must all trigger, and the alarm must be loud enough to hear in a busy unit.
8. Electrical safety
Protective earth and leakage current measurements, recorded for your equipment file.
9. Software and drug library
We record the software version and confirm the pump can accept your facility's drug library, or clear the previous owner's library so your pharmacy can load its own.
10. Cleaning and data clearing
Pumps are cleaned and disinfected with products the manufacturer approves, and the event log and any previous facility settings are cleared before delivery.
What the test report should show
- Model and serial number
- Measured flow accuracy at each test rate
- Occlusion alarm pressures and times
- Air-in-line, door and other alarm results
- Battery run time and replacement date
- Electrical safety results
- Software version and recall/field correction status
- Date and engineer's name
Reconditioned pumps from us come with a 90-day warranty. If a seller cannot provide this level of detail for each pump, treat the pump as untested.
Administration sets: check before you commit
Each pump family uses its own dedicated sets. Confirm the sets for your model are available from your supplier at a price that works, because the sets will cost more than the pump over its life. Using non-approved sets can affect flow accuracy and alarms.
Red flags when buying used pumps
- Pumps sold "tested" with no flow or occlusion results.
- No information on whether recalls or field corrections were completed.
- A previous hospital's drug library or asset tags still on the pump.
- Cracked housings or doors that do not latch firmly.
- Batteries that last only minutes, or no battery at all.
- A model whose administration sets are hard to find.
How many pumps to buy
Count the pumps in use on a busy day, then add spares for pumps that are being cleaned, charged or repaired. A small reserve keeps a failed pump from delaying a patient's therapy, and lets each pump come out of service for its scheduled checks without leaving a unit short.
Choosing the type of pump
If you have not yet decided between large-volume, syringe, PCA or ambulatory pumps, or whether you need smart pumps with a drug library, start with our guide to infusion pump types.
Delivery and service in Dallas–Fort Worth
For in-stock pumps, delivery can usually be scheduled the same day across Dallas–Fort Worth. After delivery, pumps need performance checks on the manufacturer's schedule. Our IV pump repair and rental page covers maintenance, repairs and rentals while a pump is out of service. Service requests receive a response in under 8 business hours, Monday through Friday.
To ask about refurbished IV pumps that match your fleet, call (469) 767-8853 or send us a request with the model you use now.
Leave a Comment
Comments [0]
No comments available for this blog.